100g
LED System + Battery
β οΈ
Important Warnings β Read Before Use
!
Before using this helmet, carefully read and understand all warnings and instructions. Always refer back to these guidelines before and after use. Contact the manufacturer with any questions regarding safe use.
!
The manufacturer and its associated entities assume no liability for injury, death, or damage caused by misuse of this helmet.
!
This helmet does not protect against ionizing or non-ionizing radiation, external radiation, or any risks not explicitly covered in these instructions.
!
Only manufacturer-approved components may be used with this helmet. Do not alter or modify the helmet to fit unapproved accessories or attachments.
!
This helmet absorbs shock through partial destruction of its outer shell and inner liner β damage may occur without visible signs. Replace immediately after any significant impact, even if the helmet appears intact.
!
No helmet offers complete protection against every type of impact. The helmet must fit snugly with all straps fastened for optimal safety.
!
Do not use detachable parts separately. Use the helmet only for tasks for which it has been certified and in accordance with local regulations.
β
Electrical Protection: This helmet is ANSI Class E certified, rated for up to 20,000 volts of electrical hazard protection. Suitable for use in environments where electrical hazards are present, in compliance with ANSI/ISEA Z89.1-2014 Type 1 Class E requirements.
The Cygnus 360 Safety Hard Hat sets a new standard in on-site head protection. Specifically engineered to meet CE and ANSI standards, this helmet is designed to safeguard the wearer from falling objects, reducing the risk of skull fractures and brain injuries.
The helmet absorbs impact energy through the partial deformation or destruction of the shell or harness β a design that may occur without visible external signs. Any helmet that has sustained a significant impact must be replaced immediately, regardless of appearance.
Intended Use
This safety helmet is designed specifically for head protection in construction and industrial environments. It must only be used for applications specified by the manufacturer and in compliance with local safety regulations.
πͺ
Fitting & Adjustment
The Cygnus 360 fits head sizes from 53 to 63 cm. Users with smaller head sizes may require a downsizing kit. Before each use, confirm that the helmet, suspension system, and chinstrap are correctly assembled and securely fitted.
Ratchet Size Adjustment
Use the ratchet knob at the rear of the helmet to tighten or loosen the fit until it feels firm and secure. Adjust the headband before fastening the chinstrap.
Cradle System
The cradle attaches directly to the helmet shell and is replaceable if needed. It offers two height settings for a customized fit.
3-Point Chinstrap
Side straps must sit below the ears. Pull the nape strap tight β the buckle clicks securely into place on the left side. Pull the free end to achieve a snug fit.
4-Point Chinstrap
Adjust both nape strap buckles to ensure a tight and balanced fit behind the head.
6-Point Suspension System
The internal headband offers four different placement options inside the helmet for a customized, secure fit across all head sizes in the 53β63 cm range.
π‘
Integrated 360Β° LED Lighting System
The Cygnus 360 features a professional-grade integrated lighting system powered by two 18650 Lithium-Ion cells. The system provides four distinct output modes selectable via the light button.
βοΈ
High
300 lm
All lights β full brightness
π
Medium
200 lm
All lights β medium brightness
π
Low
100 lm
All lights β low brightness
π¨
Emergency
Flashing
All lights flash at 300 lm
Battery
Two 18650 Lithium-Ion cells (2-2000). Runtime: 4β16 hours depending on selected mode.
Construction
HDPE hard hat shell with ABS plastic LED housing. Lighting system weighs 100g including batteries.
π§Ή
Cleaning & Maintenance
-
1
Clean the shell and suspension system regularly with mild soap and lukewarm water (no hotter than 40Β°C / 104Β°F). Rinse thoroughly and allow to dry before use.
-
2
Inspect the internal harness, cradle straps, and chinstraps before each use. Adjust to ensure the helmet fits snugly.
-
3
Inspect the shell for cracks, dents, or signs of impact damage before each use. Replace immediately if damage is found.
-
4
Inspect the LED system and button for proper function. Do not use if the lighting system shows signs of damage or malfunction.
β Never use the following on this helmet:
Paints Β· Solvents Β· Adhesives Β· Gasoline Β· Any chemical not approved by the manufacturer. These substances may compromise the helmet's protective capability without visible signs of damage.
β Storage warning:
Do not leave the helmet in hot vehicles. Extreme heat and UV exposure will degrade the plastic shell and make it brittle, compromising protection even without visible damage.
Always store the helmet in a clean, dry environment at room temperature, away from contaminants, chemicals, and conditions that could cause degradation.
When not in use or during transport, place the helmet in a protective container lined with foam or paper cushioning to prevent scratches or impact damage.
UV & Heat Exposure
Prolonged exposure to direct sunlight and extreme heat will degrade the HDPE shell over time. Store away from windows, vehicle dashboards, and outdoor conditions when not in active use.
π
Repair Β· Replacement Β· Retirement
Minor surface damage β may be repairable
Minor surface scratches, light paint abrasion, or superficial surface marks typically do not affect helmet performance. In such cases, the helmet may be restored using warm wet sanding to remove surface imperfections and stains.
β Replace or destroy the helmet immediately if any of the following are present:
- βDeep indentations, crushing, or visible laminate damage from impacts
- βCracks extending through to the interior of the helmet, compromising structural integrity
- βSignificant cracks or abnormal bending in the brim area
- βSigns of charring, burning, or excessive heat exposure (visibly burnt areas or substrate damage that cannot be corrected through sanding)
- βVisible residues of acids or chemicals that may have weakened the shell or paint
- βShell deformation β sagging, drooping, or warping of any kind
- βThe helmet can no longer be properly adjusted to fit securely
- βAny component fails inspection or appears unsafe for any reason
- βThe helmet has sustained any significant impact β even if no visible damage is present
Spare Parts & Accessories
Approved spare parts and accessories are available. Contact the manufacturer for replacement components or questions about correct assembly. Do not alter or modify the helmet to fit unapproved attachments.
β
Certifications & Compliance
ANSI Z89.1-2014
Type 1 Β· Class E
Rated for 20,000V electrical hazards
FCC Certified
Electronic emissions
IP53 Rated
Dust & water resistance
